no

Washing Machine: Five Most Common Problems Blog

Washing Machine: Five Most Common Problems Blog

OK, today I wanted to go over the five most common problems with washing machines with you.

00:19 The number one most often problem with washing machines is a washing machine that doesn’t drain or spin, most often caused by a broken lid switch.

You should hear a click as this goes into place. If you don’t hear that click then your, or if your washing machine is not going into its final cycles
it’s most often this lid switch here.

Sometimes you can just press on this right side and get it to engage the switch. Also occasionally you can just adjust the post a little bit
so that the post will stick further into the switch which will engage the switch. Also sometimes you can just adjust the switch or tighten it up.
Often it needs to be replaced I have a video on that.

01:05 Second most often problem with washing machines often goes undetected something you’d probably want to check regularly is that your agitator dogs are working properly. What it should do is turn the bottom one-way or the other. So this one is turning it like it should and the agitator dogs are functioning. Now if it’s not doing that than your clothes are just getting rinsed. They are not really getting washed. It is an often missed
problem with washing machines. And it is probably very common because the agitator dogs inside here are designed to break if someone’s arm was to get stuck in here or if something was to bind up too much the agitator dogs will actually strip on purpose as a safety mechanism.

01:50 Third most common problem with washing machines is a clogged pump at the impeller. Sometimes a penny or a button, or something else, a bobby pin, whatever goes down the drain line and gets stuck at the pump.

02:05 Fourth most common problem is a leak. Most often leaks occur up on the left side.

Fifth most common problem is a washing machine out of balance. Now the most often cause of the machine being out of balance is just a matter of redistributing the clothes. Usually a towel or something gets on one side and you hear the whump whump whump whump of the machine.

What you need to do is open the lid and than go ahead and readjust the clothing or go ahead and readjust the towel. Readjust the items in the bin to get it more balanced. Then go ahead and run it again see if it works out and you have no more out of balance deal.

Sometimes you could lose a spring. Most often times it’s just that the
machine is out of balance. Eventually I’ll have to make you a video showing you how to reset the spring if it did come off.

There are three different shocks and then there is a spring that holds the machine basin in place.

Now the way to check if your machine is still in balance is just ahead and run it empty with water. Let the water fill up. If the machine finds its balance than you know it was just a matter of the clothes or the laundry items being out of balance

Anyway that is the five most common problems with washing machines!

~ TFW ~..~ KFM ~

Posted by Kung Fu Maintenance in The KFM Blog, Tips, 0 comments

Fridge Not Cooling ~ First Thing To Check For Blog

00:13 Got A fridge not cooling here
00:15 and you can hear the compressors kicked on
00:19 but you can hear one of the first things to check for is that the fan is not kicking on
00:25 so it could just be that the fan is stuck
00:28 so
00:29 what we’re gonna do is remove this ice tray deal
00:33 just by pushing up here
00:36 and sliding this out and there is two screws on the back that hold the fan channel in
00:42 so I’m gonna remove these two screws here
00:46
00:51 and this is one of the first things to check for when you’ve got a fridge that is not cooling
00:56 check for a stuck fan motor first
01:00 now that may not be the only thing going on
01:04 lift this fan channel up here and slide it out
01:07 ok
01:10 and there is our fan, you can see it’s not spinning very fast
01:14 It should be spinning faster than that
01:18 And chances are what it is is that it is too close
01:23 the fan blade is too close
01:24 see how it was rubbing against the back
01:27 and that’s why it wasn’t spinning very fast
01:29 so what I’m gonna do is pull that forward a little bit more
01:36 it’s probably a little bit safer to
01:39 turn the power off first but I’m just gonna get this done
01:44 ok
01:45 I took the whole thing off there
01:48 anyway place this on and now it’s out a little bit more and doing what it should now that was keeping the air from being able to blow down into the fridge and the freezer wasn’t circulating the air like it should
02:13 behind the fan channel on this side it’s got an adjustment here
02:14 you usually don’t have to adjust these to much
02:17 but if you wanted your freezer to be colder or needed your freezer to be colder you can adjust this dial by pulling out and turning that, each model has it’s own peculiarities. Ok now that we’ve got the fridge fixed theoretically what we need to check for is
02:34 under the pan to see if there is any ice there which there probably is and the freezer drain line is probably clogged
02:40 The way we can tell this is if we’ve got water dripping
02:43 down here
02:44 which we do so were going to need to clear that out
02:47 but I will put that on the next video.

Posted by Kung Fu Maintenance in The KFM Blog, Tips, 0 comments

Getting Vertical ~ Repairing Vertical Blinds

Let us say you go to open your vertical blinds and oh no, the blinds won’t open. The first thing to check for is any blind slats that are out of line with the others. Look for any that are overlapping the others the wrong way and push the top corner to set it the right way. This is the most often needed repair for vertical blinds. Blinds often get out of alignment due to wind, people, pets, vacuums, chairs etc…

 

 

A bigger problem is when one of the gears gets turned out of step with the other gears. The repair is performed by turning the stem the right way. Sometimes you can grab the stem and turn it with your hand. Take care not to bend the slat itself or it may break. Often you will need or want to remove the slat. That makes it easier to grab the stem with a pair of pliers and then pop it over.

This repair sometimes causes a gear tooth to break. Replacing stem gears is fairly easy and I will try to make a video for that repair in the future. I cover all of these repairs and much more in my book, Kung Fu Maintenance. I have another video at present titled The Master Blind Gear. I hope you like it and that it serves you well. It covers (as you probably guessed) how to replace a stripped master blind gear controller for vertical blinds.

Be extra careful when working with blinds and appliances as the metal is often unfinished metal and very sharp. I have given blood numerous times. A little precaution makes for a better day.

~~~ Get Vertical ~~~ Stay Above Horizontal ~~

~~~~~~~~~~~~~~~~~~ Kung Fu Maintenance ~~~~~~~~~~

Posted by Kung Fu Maintenance in The KFM Blog, 0 comments